Published by the California Seismic Safety Commission
Homeowner’s Guide
to Earthquake Safety
2020 EDITION
State of California
Gavin Newsom
Governor
SSC No. 20-01
The Homeowner’s Guide to Earthquake Safety
was developed and published by the California
Seismic Safety Commission. It is distributed
under the provisions of the Library Distribution
Act and Government Code Section 11096.*
Copyright 2020 by the California Seismic Safety Commission.
All rights reserved.
Legislation
This guide has been developed and adopted by the
California Seismic Safety Commission as required by
Assembly Bill 2959, authored by Assemblymember
Johan Klehs (Chapter 1499, Statutes of 1990), and by
Assembly Bill 200, authored by Assemblymember
Dominic Cortese (Chapter 699, Statutes of 1991).
Ordering Information
Single copies of this booklet are available from the
California Seismic Safety Commission
2945 Ramco St. #195
West Sacramento, CA 95691
To order call (916) 263-5506 or download an online copy at
http://ssc.ca.gov/forms_pubs/index.html
Cover photo: Collapsed two-story home. Nigel Spiers, 2011
Shutterstock, Enhanced License
*Disclaimer: The effects, descriptions, recommendations and suggestions included in
this Guide are intended to improve earthquake preparedness; however, they do not
guarantee the safety of an individual or a structure. The California Seismic Safety
Commission takes responsibility for the inclusion of material in this Guide. The State
of California, the California Seismic Safety Commission, and all contributors to this
document do not assume liability for any injury, death, property damage, loss of
revenue, or any other effects of earthquakes.
Effective July 1, 2020, the 2020 edition of the Homeowner’s Guide
to Earthquake Safety replaces the 2005 edition.
California Seismic Safety Commission
USING THIS GUIDE PAGE
Selling or Buying a Home ....... 4
Earthquake Hazards in
California ................................. 6
Residential Earthquake Risks &
the Disclosure Statement ........ 12
Tips for a Successful
Retrofit .................................... 26
Earthquake Safety Tips ........... 30
Other Information ................... 34
$
5
BILLION
5
+
Earthquake -
related losses
in California
since 1971
$
1
BILLION
2
+
Estimated home
damage in the
1994 Northridge
Earthquake
Introduction
EARTHQUAKES ARE
INEVITABLE IN CALIFORNIA.
They can occur at any time and without warning.
They can be extremely destructive and even deadly.
As a current or future owner of a home*, you
should be aware of the risks—potentially
considerable and catastrophic—that earthquakes
pose to your property and to the safety of you
and your family.
THIS GUIDE is designed to help you prevent injuries, save
lives, and avoid costly property damage from earthquakes.
It provides information on:
The most common earthquake-related hazards that
can damage homes
How to find and then fix the potential structural risks
in a home
How to find more information on earthquake safety
If you sell your home, this Guide also will help you meet
your requirements under California law.
There are no guarantees of safety during earthquakes,
but properly constructed and strengthened homes are far
less likely to collapse or be damaged during earthquakes.
The California Seismic Safety Commission advises you to
act on the suggestions outlined in this Guide and make
yourself, your family, and your home safer.
*In this Guide, “home” means single-family residences, duplexes, triplexes, and
four-plexes. Under California law, a seller of a home built before 1960 must fulfill
certain disclosure requirements as part of the sales process (see page 4).
PAGE 3
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Selling or Buying
A Home: Requirements
& Recommendations
SELLING A HOME
If you are selling a home built before 1960, California law*
requires you to:
Properly strap the water heater.
Provide buyers with the following documents:
o
A Residential Earthquake Risk Disclosure Statement
(page 13), where you identify known home risks
o
A Natural Hazard Disclosure Statement, where you
indicate if your home is in an Earthquake Fault Zone or
Seismic Hazard Zone. Ask your realtor for a copy of this
Disclosure Statement.
o
A copy of this Guide (Your real estate agent is required
to give you the Guide.)
o
Note: If you list your home through a real estate agent
or broker, you should have him or her give the
documentation to the buyer.
Note: Keep a copy of all documentation signed by the buyer
as evidence that you complied with the requirements.
Under the law, you are NOT required to:
Remove siding, drywall, or plaster to complete the
disclosure statements.
Hire someone to evaluate your home or to complete the
disclosure statements. You may seek the assistance of a
certified home inspector or a licensed contractor, architect,
or engineer.
Fix the risks before you sell your home; on the other hand,
making the improvements could increase your home‘s value.
*A summary of the relevant California laws related to seismic safety is included at the end
of this Guide (page 35).
PAGE 4
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
BUYING A HOME
Before you agree to buy a home, you should consider the following:
Have a certified home inspector, licensed building contractor,
engineer, or architect inspect the home and give an opinion on
existing earthquake risks and the estimated cost to strengthen
the home.
Check the location of the home to determine if it is in an
Alquist-Priolo Earthquake Fault Zone or an area susceptible to
landslides, liquefaction, or tsunami. A licensed geotechnical
engineer and/or engineering geologist can help you answer these
questions and check the stability of the land under the home.
Negotiate with the seller the cost of any proposed repairs or
upgrades. State law does not require either the seller or buyer to
strengthen a home against earthquake risks. However, the cost to
repair a home after a damaging earthquake may far exceed the
costs to strengthen the home and reduce the risks.
Property Tax Exclusion
Under California law (Revenue and Tax Code, Section 74.5), a homeowner
can implement seismic-strengthening measures without a property tax
reassessment. To receive the exclusion, you must have the work approved
by the local building department and file a claim form with your county
tax assessor.
Earthquake Insurance
Typically, residential property insurance does not include earthquake
coverage. A homeowner may purchase a separate earthquake policy.
Information on earthquake insurance is on page 37.
PAGE 5
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Earthquake Hazards
Is your home
near an active
earthquake
fault or an area
prone to severe
shaking?
See the maps on
pages 10 & 11.
KNOW IF YOUR HOME
IS AT RISK
Earthquakes occur in California every day. As a homeowner,
you should know if your home is in an area that is more prone
to earthquakes or if the geology or soil conditions of your
neighborhood or community present greater risk during an
earthquake. The more you know, the better able you are to
take appropriate precautions to protect your home and family.
Requirements under the law: If you are selling your home or
any other type of real estate, no matter its age, you must
disclose to buyers information about natural hazards that can
affect the property, including flood and fire hazards and
earthquake hazards. You report this information on the Natural
Hazard Disclosure Statement.
The most common earthquake-related natural hazards are
ground shaking, fault ruptures, landslides, liquefaction, and
tsunami. In addition, earthquake damage to a dam can be a
hazard to “downstream” homes.
PAGE 6
Pilar Villamor, GNS Science, 2016
A strong earthquake can
cause the two sides of a
fault to suddenly slide by
one another. Even a
relatively minor fault rupture
can cause foundation and
structural damage requiring
expensive repairs.
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Earthquake Hazards
GROUND SHAKING
Guy Morrow, 2004
In California, ground shaking causes 99% of earthquake damage to homes. Homes in areas
near large active faults are more likely to feel severe shaking—and experience damage—
than homes in other areas of the state.
FAULT RUPTURE
PAGE 7
PAGE 8
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Earthquake Hazards
Earthquake shaking can
be strong enough to cause
soil and rock on a hillside
to slide down the slope.
A landslide can rip apart
homes at the top of the
slope and also crush
homes at the bottom of
the slope.
Al Seib, Los Angeles Times, 1994
LANDSLIDE
LIQUEFACTION
Graeme Beattie, BRANZ, 2011
Strong ground shaking can cause liquefaction—excess pore
water pressure that reduces the soil’s ability to support structures.
Liquefaction can cause structures to tilt or collapse.
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Earthquake Hazards
Is your home
at risk of a
tsunami?
Check with your
County’s office
of emergency
services.
TSUNAMI
National Oceanographic and
Atmospheric Administration, 1964
California’s coastal areas are prone to damage from tsunami—a series of large ocean
waves caused by an underwater earthquake or landslide. Tsunami waves can travel
a great distance and cause flooding or wash away structures in low-lying areas
along the shore, in and along harbors, and along the banks of rivers. Tsunamis
generated by the 1964 Alaskan earthquake (magnitude 9.2) and the 2011 Japan
earthquake (magnitude 9.0) caused property damage and loss of life in California.
DAM FAILURE
A very strong earthquake could damage a dam, resulting in
sudden and devastating flooding of nearby homes. The 1971
San Fernando earthquake damaged the Lower San Fernando
Dam, which sits less than half-mile above the neighborhoods of
the San Fernando Valley in southern California. The risk of an
aftershock forced the three-day evacuation of residents of an
11-square-mile area.
E. V. Leyendecker,
United States
Geological Survey,
1971
Is your home
near a dam?
Check with your
County’s office of
emergency services
for a dam inundation
map, which shows the
location of major
dams and areas that
could flood in the
event of
a dam failure.
BETTER SAFE THAN SORRY
If you live in a low-lying coastal area or an area near a dam (dam
inundation zone), know where to evacuate to higher ground and
be prepared to evacuate immediately after an earthquake.
PAGE 9
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
$
BILLION
3
+
PER YEAR
Expected
long-term
average
earthquake
damage in
California
Earthquake Shaking Potential
for California
This map shows the relative intensity of ground shaking in
California from anticipated future earthquakes and significant
earthquakes that have occurred since the Great 1857
magnitude 7.9 Fort Tejon earthquake. Although the greatest
hazard is in areas of highest intensity as shown on the map,
no region is immune from potential earthquake damage.
EUREKA, 1980
EARTHQUAKE MAGNITUDE
M 5.6–6.5
M 6.6–7.0
M 7.1–7.9
EUREKA, 1954
OROVILLE, 1975
CAPE MENDOCINO,
1992
TAHOE, 1966
WINTERS/Vacaville, 1892
SANTA ROSA, 1969
SOUTH NAPA, 2014
SAN FRANCISCO, 1906
MORGAN HILL, 1984
LOMA PRIETA. 1989
COALINGA, 1983
SAN SIMEON, 2003
KERN COUNTY, 1952
BIG BEAR, 1992
HECTOR MINE, 1999
LANDERS. 1992
PALM SPRINGS,
1986
Level of Earthquake Hazard
These regions are near faults and
will on average experience stronger
earthquake shaking more frequently.
This intense shaking can damage
even strong, modern buildings.
SANTA BARBARA, 1925
Increasing
Intensity
These regions are distant from known
faults and will experience lower levels
of shaking less frequently. In most
earthquakes, only weaker, masonry
buildings would be damaged.
However, very infrequent earthquakes
could still cause strong shaking here.
Water
EL MAYOR-CUCAPAH, 2010
MAMMOTH LAKES, 1980
CHALFANT VALLEY, 1986
OWENS VALLEY, 1872
FORT TEJON, 1857
SAN FERNANDO, 1971
NORTHRIDGE, 1994
SIERRA MADRE, 1991
WHITTIER NARROWS. 1987
LONG BEACH, 1933
SUPERSTITION HILLS, 1987
IMPERIAL VALLEY, 1940
IMPERIAL VALLEY, 1979
RIDGECREST, 2019
Source: California Geological Survey Map and U.S. Geological Survey
PAGE 10
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Significant Historical Earthquakes and
Their ShakeMaps
The ShakeMaps (inserts) show areas of moderate-to-heavy ground shaking
in four historical earthquakes.
ShakeMap Explanation
I II-III IV V VI VII VIII IX X+
Source: USGS
EARTHQUAKE MAGNITUDE
M 5.6–6.5
M 6.6–7.0
M 7.1–7.9
1992 M 7.2 Petrolia
1989 M 6.9 Loma Prieta
1994 M 6.7 Northridge
1906 M 7.8 San Francisco
PAGE 11
IN THIS SECTION PAGE
Completing the Residential
Earthquake Risk Disclosure
Statement ...........................12-13
Identifying and Disclosing
Earthquake Risks ................ 14-25
Water Heaters .............................. 14
Unbolted Foundations ................. 15
Crawl Space (Cripple) Walls ......... 17
Pier-and-Post Foundations ........... 18
Unreinforced Masonry
Foundations ................................. 19
Hillside Homes ............................. 20
Unreinforced Masonry Walls
......... 21
Rooms over Garages ................... 22
Unreinforced Masonry
Chimneys ..................................... 23
Inadequate Foundation ............... 24
Homes with
Unique Designs ............................ 25
You are not required to remove
siding, drywall, or plaster or to hire
an inspector to determine the
answer to a question. Also, you are
not required to fix or retrofit your
home before you sell the property.
Residential
Earthquake Risks & the
Disclosure Statement
Earthquakes in California can occur at any time and without
warning. To prevent injuries and avoid costly property
damage, homeowners should determine the potential for
earthquake risks in their homes and then retrofit or upgrade
these conditions. If not corrected, these risks can lead to:
Severe property damage, including foundation
damage and damage to floors, walls, and windows
Loss of personal property
Broken utilities, which can result in fire, water damage,
and spread of toxic substances
Personal injuries
In addition, under California law, sellers of homes built
before 1960 must disclose known earthquake risks to
buyers as part of the property sales process.
Completing the Residential Earthquake Risk
Disclosure Statement
When you sell a home built before 1960, you are required to
fill out the Residential Earthquake Risk Disclosure Statement,
(see next page) and give the completed statement to the
buyer. You are required to answer each question to the best
of your knowledge.
To complete the Disclosure Statement, answer:
“Yes” if you know your home is protected from the risk
(e.g., for Item #1, answer “Yes” if your home’s water
heater is properly braced)
“No” if you know your home is at risk (e.g., for Item #6,
answer “No” if your home’s exterior brick walls are not
strengthened)
“Doesn’t Apply” if the question is not relevant to your
home (e.g., for Item #7, answer “Doesn’t Apply” if your
home does not have a living space over the garage)
“Don’t Know” if you do not have adequate information
to answer the question
PAGE 12
b. Are the tall posts or columns either built to resist earthquakes or have
they been strengthened?
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Residential Earthquake Risk Disclosure Statement
(2020 Edition)
Name Assessor’s Parcel No.
Street Address Year Built
City County Zip Code
Answer these questions to the best of your knowledge. If any of the questions are answered “No,” your home is likely to
have an elevated/disclosable earthquake risk. If you do not have actual knowledge as to whether these risks exist, answer
“Don’t Know.” Questions answered “Don’t Know” may indicate a need for further evaluation. If your home does not have
the feature, answer “Doesn’t Apply.” If you corrected one or more of these risks, describe the work on a separate page.
The page numbers in the right-hand column indicate where in this guide you can find information on each of these features.
Doesn’t Don’t See
Yes No Apply Know Page
1. Is the water heater braced to resist falling during an earthquake?
˜ ˜ ˜ ˜ 14
2. Is your home bolted to its foundation?
15
3. If your home has crawl space (cripple) walls:
a. Are the exterior crawl space (cripple) walls braced?
17
b. If the exterior foundation consists of unconnected concrete piers and
posts, have they been strengthened?
˜ ˜ ˜ ˜ 18
4. If the exterior foundation, or part of it, is made of unreinforced masonry,
19
has it been strengthened?
5. If your home is on a hillside:
a. Are the exterior tall foundation walls braced? 20
˜ ˜ ˜ ˜ 20
6. If the exterior walls of your home are made of unreinforced masonry,
either completely or partially, have they been strengthened?
21
7. If your home has a room over the garage, is the wall around the garage door
opening built to resist earthquakes or has it been strengthened?
˜ ˜ ˜ ˜ 22
8. Is your home outside an Alquist-Priolo Earthquake Fault Zone (an area
immediately surrounding known active earthquake faults)?
To be reported on the Natural
Hazard Disclosure Statement
9. Is your home outside a Seismic Hazard Zone (an area identified as susceptible
to liquefaction or a landslide)?
To be reported on the Natural
Hazard Disclosure Statement
As seller of the property described herein, I have answered the questions above to the best of my knowledge
in an effort to disclose fully any potential earthquake risks it may have.
EXECUTED BY
Seller Seller Date
I acknowledge receipt of the Homeowner’s Guide to Earthquake Safety and this Disclosure Statement, completed and
signed by the seller. I understand that if the seller has answered “No” to one or more questions, or if the seller has
indicated a lack of knowledge, there may be one or more earthquake risks in this home.
Buyer Buyer Date
This Disclosure Statement is made in addition to the standard real estate transfer disclosure statement also
required by law.
PAGE 13
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Earthquake Risk Disclosure Statement Item 1
During an earthquake,
an unbraced water
heater can topple,
which can start a fire
or lead to major water
damage.
Is your home’s water heater
braced?
If your home’s water heater is not properly braced, or if it has
rigid rather than flexible pipes, the water heater may move
or topple during an earthquake. This movement can break gas
or water lines, resulting in fire, water damage, or release of
toxic gas.
Under California law, you are required to brace your home’s
water heater whenever you install a new water heater or if you
sell the home.
How to Check for Proper Water Heater Bracing
1. Examine your home’s water heater.
2. Look for two sets of straps that wrap around the water
heater and securely bolt the water heater to the wall and
wall studs (see diagram).
Tankless Water Heater?
If you have a tankless water heater, be sure it is securely attached
to the wall and that its pipes are installed according to the
manufacturer’s instructions.
PROPER WATER HEATER BRACING
Sheetrock
WANT TO RETROFIT?
Find out more on pages 26-29.
PAGE 14
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Earthquake Risk Disclosure Statement Item 2
Is your home bolted to its foundation?
If your home is not bolted to its foundation, it could slide off the foundation
during an earthquake.
A home that has moved can cause gas, water, and sewer lines to
break, resulting in fire, water damage, and release of toxic fluids.
Lifting a home back onto its foundation is difficult and expensive.
How to Check for Foundation Bolting
1. Determine if your home has a crawl space, which will be below the
first floor.
Clue: If your home has steps leading to an exterior door, the home
probably has a crawl space. If you have no steps, the home is most likely
built on a concrete slab and has no crawl space. If you do not have a
crawl space, see “What If”section on next page.
2. Go into the crawl space. Access will be through a small removable panel
or door along an exterior wall or from inside the garage.
3. Look for areas of unfinished wood framing at base of walls (see diagram).
If the crawl space has finished wood framing, see “What If”section.
4. Find sill plates (wood boards that sit directly on top of foundation) and
look for anchor bolts that fasten sill plates to foundation (see diagram on
next page).
Adequate bolting: Bolts with nuts and square washers spaced every
4 to 6 feet
Inadequate bolting: No visible bolts
WANT TO RETROFIT?
Find out more on pages 26-29.
PAGE 15
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
WHAT IF . . .
Q
My home does not have a crawl space?
A Particularly after 1960, many California homes were built
directly on concrete slabs. Fortunately, most of these homes
and other post-1960 homes built to code have anchor bolts.
Q The crawl space has finished framing, so I cannot see the
sill plates or anchors?
A You are not required to remove siding, drywall or plaster to
determine if your home’s foundation has anchor bolts.
For both situations, check “Don’t Know” on the Disclosure Statement.
LOCATING FOUNDATION BOLTS
WANT TO RETROFIT?
Find out more on pages 26-29.
PAGE 16
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Earthquake Risk Disclosure Statement Item 3a
Are your crawl space
(cripple) walls braced?
If your home has a crawl space with un-braced walls,
these crawl space (cripple) walls could collapse during an
earthquake, which, in turn, may cause your entire home
to collapse or lead to major damage to the structure as
well as possible fire, water line breaks and injuries.
How to Check for Bracing of Crawl Space Walls
1. Determine if your home has a crawl space with cripple walls.
Clue: If your home has three or more steps leading to an exterior door,
the home has a crawl space below the first floor and, therefore, has
cripple walls.
2. Go into the crawl space. Access will be through small removable panel or
door along an exterior wall or from inside the garage.
3. Examine the inside surfaces of the exterior walls.
Adequate bracing: Plywood or diagonal sheathing on exterior walls
(see diagrams)
Inadequate bracing: No plywood or diagonal sheathing
DIAGONAL SHEATHING
This older home
collapsed after
earthquake
shaking
damaged its
crawl space
(cripple) walls.
PLYWOOD OR ORIENTED
STRAND BOARD
WANT TO RETROFIT?
Find out more on pages 26-29.
PAGE 17
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Earthquake Risk Disclosure Statement Item 3b
If your home sits on large wood posts that rest on
unconnected concrete piers, the posts may not be braced
properly. During an earthquake, the posts could fail and
your home could shift or collapse.
How to Check for Pier-and-Post Foundation Strengthening
Is your home’s pier-and-post
foundation strengthened?
This home’s pier-and-post
foundation was damaged
during an earthquake.
The diagonal bracing was
added after the earthquake
to temporarily stabilize the
home during repairs.
1. Go under the home and determine the type of foundation
that supports the exterior walls.
Continuous perimeter foundation wall (check “Does Not
Apply” on the statement)
Concrete piers and wood posts
2. For concrete piers and wood posts, look further to determine
if the foundation is adequately braced or strengthened.
Adequate bracing: A continuous foundation around the
perimeter edges of the home that consists of either
reinforced concrete or reinforced masonry.
Inadequate bracing along the perimeter edges of the home:
o
Wood posts supported by concrete piers, or
o
Wood posts without concrete piers or continuous
perimeter foundations
WANT TO RETROFIT?
Find out more on pages 26-29.
PAGE 18
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Earthquake Risk Disclosure Statement Item 4
Is your home’s unreinforced
masonry foundation
strengthened?
If your home is supported by a brick, stone or concrete block
foundation that lacks steel reinforcing, the foundation may
not be able to resist earthquake shaking. Your home could
slide off its foundation during an earthquake, damaging the walls and
floors, rupturing utility connections, and destroying the contents of
your home. This, in turn, could lead to fire, water damage, and injuries.
How to Check an Unreinforced Masonry Foundation
1. Walk around the perimeter of your home to determine the composition of
the foundation. If the foundation has siding or a plaster finish, you will need
to check the foundation from inside the crawl space.
Solid concrete foundation (check “Does Not Apply” on the statement)
Unreinforced brick, stone, or concrete block foundation
2. For unreinforced brick, stone, or concrete block foundation, look further
to determine if the foundation is adequately braced or strengthened
(e.g., steel plates attached to foundation walls). If you do not know what
to look for, consult a licensed engineer or architect.
WANT TO RETROFIT?
Find out more on pages 26-29.
PAGE 19
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Earthquake Risk Disclosure Statement Item 5
The balcony of this
hillside home partially
collapsed and the home
tilted when the
stilt-type support posts
and poorly braced walls
shifted during an
earthquake.
Does the foundation of
your hillside home have
adequate support?
Hillside homes require special engineering to resist
earthquake shaking.
If your home is built on a hillside and the home’s tall foundation
walls and stilt-type support posts are not properly braced, your
home could collapse during an earthquake, causing severe
damage to the home and injuries.
How to Check the Foundation of a Hillside Home
1. Walk around the perimeter of your home to examine both the
tall foundation walls and the tall posts or columns that support
the home.
2. Examine the exterior tall foundation walls for evidence of
extensive wall bracing below the home.
3. If you do not know what to look for, consult a licensed engineer
or architect.
WANT TO RETROFIT?
Find out more on pages 26-29.
PAGE 20
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Earthquake Risk Disclosure Statement Item 6
Are your home’s unreinforced
masonry walls strengthened?
If your home has walls built of unreinforced masonry—
brick, hollow clay tiles, stone, concrete blocks, or
adobe—the walls may be too brittle to resist earthquake
shaking. As a result, the walls could collapse in an
earthquake.
How to Check for Unreinforced Masonry Walls
1. Walk around the perimeter of your home to examine the composition of
the exterior walls. Look for evidence of unreinforced brick, clay tile, stone,
adobe, or concrete-block wall construction.
Look closely at wall surfaces at windows and doors.
If the exterior walls are covered with plaster, examine the walls from
inside the home (e.g., beneath light switch plates).
2. If the exterior walls are built of masonry, check further for the strength of
construction or for indicators of retrofit. Steel plates and anchor bolts are
common retrofits (see photo).
PAGE 21
3. If you do not know what to look for, consult a licensed engineer
or architect.
A steel plate with anchor bolts.
WANT TO RETROFIT?
Find out more on pages 26-29.
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Earthquake Risk Disclosure Statement Item 7
If your home has a room above the garage, you need to ensure
that the narrow walls on either side of the garage doorway are
strong enough to withstand earthquake shaking. Without
adequate support, these walls could collapse, causing serious
damage and injuries.
How to Check the Strength of a Garage with a Room Above
Does your home have a
room above the garage?
The walls around the
garage door of this home
were not strong enough
to withstand the shaking
of the 1989 Loma Prieta
Earthquake.
1. Go into your garage and examine the walls on both sides
of the garage doorway. If the garage has been built or
strengthened to support a second story, you will see plywood
bracing on the walls and metal straps (see diagram).
2. If you do not know what to look for, consult a licensed
engineer or architect.
GARAGE WALL BRACING
Adequate bracing for a garage wall includes
plywood and metal straps.
WANT TO RETROFIT?
Find out more on pages 26-29.
PAGE 22
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Other Structural Risks
Your home also may have other structural issues that could result in serious
property damage or injuries during an earthquake. These risks are not included
in the Residential Earthquake Risk Disclosure Statement because, typically, it is
not cost effective to complete a retrofit. On the other hand, these risks should
be considered if you are a homeowner or a potential home buyer.
UNREINFORCED MASONRY CHIMNEY
If your home has an unreinforced brick or stone chimney, it could
collapse during an earthquake and fall on the ground beside the
home or fall through the roof into your home (see photos).
How to Check Your Chimney
To determine if your chimney will withstand an earthquake:
1. Check the mortar with a screwdriver. If the mortar crumbles,
it may be too weak to withstand earthquake shaking.
2. Access the attic area above the fireplace to verify that the
chimney is securely attached to the home with metal straps
or ties.
3. If you are unable to verify the strength of the chimney, consult
a licensed engineer or architect or a general contractor.
How to Protect against Damage and Injuries
(Safety Precautions)
Avoid parking cars or locating patios or children’s play areas
within the falling radius of a chimney.
Remind home occupants to stay away from chimneys and
fireplaces during earthquakes.
California Earthquake
Authority, 2014
Bay Area Regional
Earthquake
Preparedness
Project, 1989
WANT TO RETROFIT?
Find out more on pages 26-29.
PAGE 23
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Other Structural Risks
INADEQUATE FOUNDATION
A wood foundation or a foundation of concrete or masonry that
is cracked or crumbling may not have the strength to withstand
earthquake shaking.
How to Check the Condition of Your Foundation
Determining if a foundation is susceptible to earthquake damage
can be a challenge, and the advice of a licensed engineer or
architect or a foundation contractor may be necessary.
Wood foundation: In the past, some homes were built on
wood beams laid directly on the ground without concrete or
masonry supports. If you do not see concrete or masonry
damage.
foundation walls along the perimeter of your home, your
home may have a wood foundation.
Deteriorating masonry: Older concrete or stone
foundations can deteriorate over time and become too
weak to withstand earthquake shaking. Large cracks,
crumbling, or rock pockets are visual signs of deterioration.
You also can poke a screwdriver into a foundation wall
to check its strength; if the concrete or stone crumbles
easily, the foundation may be vulnerable to earthquake
WANT TO RETROFIT?
Find out more on pages 26-29.
PAGE 24
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Other Structural Risks
HOMES WITH UNIQUE DESIGNS
If not designed adequately and with earthquakes in mind, homes with
unique designs can be prone to damage from earthquake shaking.
Unique design features include homes with:
Large porches or overhangs
Large windows or window walls
Three or more stories
Irregular shapes
Evaluation and Options
In many cases, homes with unique designs have been built to withstand
earthquake shaking. Identifying if a home has been strengthened can be
difficult. Consulting with a licensed engineer or architect for a seismic
evaluation canbe helpful.
You can make large windows safer by applying plastic film to the glass.
WANT TO RETROFIT?
Find out more on pages 26-29.
PAGE 25
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Tips for a Successful
Retrofit
MAKE A PLAN: DEFINE THE SCOPE OF WORK AND
HOW TO ACCOMPLISH THE PROJECT
The first step in an earthquake retrofit or upgrade is to ensure
that you, as the homeowner, understand the work that will be
required for the retrofit project and the required building and
performance standards. You should not rush into repairs, no
1
matter how badly they are needed, or hire the first contractor
2
you meet with.
3
Define Scope of Work
Defining the scope of a retrofit or upgrade project is a critical
first step. Additional resources are listed on page 34.
Reminders:
• For any retrofit project, be sure to consult with your local
building department for advice on the State’s requirements,
local building codes and standards.
• To determine the best solution for a retrofit, you may want
to consult a licensed engineer or architect or a general
contractor that specializes in this type of work.
You or your contractor will need to obtain a building permit
from your local building department.
When evaluating the cost of a retrofit, remember to
consider both the economic value of the work and the
value to your “peace of mind.”
PAGE 26
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Water Heater Bracing
Under California law, you are required to brace the water heater when you
install a new water heater and when you sell your home.
You can brace a water heater yourself using a strap kit, available from a local
hardware store. Or, you can hire a plumber or handyperson to do the work.
The diagram on page 14 illustrates proper water heater bracing.
As an added safety precaution, consider having a licensed plumber replace
any rigid pipes with flexible pipes, which will better withstand shaking during
an earthquake.
Simple Retrofit Projects
The California Existing Building Code, Appendix A, Chapter A3 contains
how-to information for retrofitting. FEMA P-1100, Volume 2A is also easy to
use and accepted for retrofits by local building departments. Do-it-yourself
homeowners can undertake simple retrofits without hiring an engineer,
architect, or contractor.
Types of Simple Retrofit Projects
Foundation bolting: To add or retrofit a foundation bolting system
requires drilling new holes into the foundation and installing bolts.
Crawl space wall bracing: To add or retrofit the wall bracing in a crawl
space requires nailing new plywood or oriented strand board to crawl
space studs. Note: For crawl spaces taller than four feet, consult
FEMA P-1100, Volume 2A.
More Complicated Retrofit Projects
By their nature, some earthquake retrofit projects are more complicated and
will require the expertise of a licensed engineer or architect and/or a general
contractor who specializes in this type of work.
Pier-and-post foundation: You may be able to strengthen a
pier-and-post foundation system adequately with bracing; alternatively,
the best solution may be to install a new, continuous foundation.
PAGE 27
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Unreinforced masonry foundation: You may be able to
replace or supplement all or part of an existing foundation
with a new reinforced concrete or masonry foundation.
Other inadequate foundation: If your home’s foundation is
inadequate (see pages 19, 24), you may need to add a new
or replace an existing foundation to reduce the risks of
earthquake damage.
Unreinforced masonry walls: In most cases, retrofitting
unreinforced masonry walls requires 1) better connecting the
walls to the roof and floors and 2) installing steel frames or
reinforced concrete. In some cases, large steel plates must be
attached with anchor bolts through the masonry (see photo
on page 21). Engineering information is in the California
Existing Building Code, Appendix A, Chapter A1.
Unreinforced masonry chimney: Strengthening or bracing a
chimney can be expensive. Retrofit options include:
o Adding plywood panels either above ceiling joists or,
when re-roofing, on roof framing
o Removing or replacing all or a portion of the chimney with
lighter-weight material (e.g., using a metal flue for the upper
portion of a chimney). (see FEMA P-1100, Volume 2C)
Garage walls: Engineering information on retrofitting
garage walls is in the California Existing Building Code or
FEMA P-1100, Volume 2B.
Hillside homes: Retrofitting hillside homes includes
strengthening foundations, walls, columns and diagonal
bracing. Engineering information is in the California Existing
Building Code or the FEMA P-1100 publication.
Historical homes: Your project will need to comply with the
California Historical Building Code.
Keep Your Retrofit Documents
Once your project is complete, remember to keep all plans, permits,
and other project records so you can provide them to a future
home buyer.
PAGE 28
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Select a Licensed Contractor
A critical step is to find and hire the right contractor for your job.
Be sure you:
Discuss your project with at least two and, ideally, more
licensed contractors.
Obtain a written proposal from each contractor. Do not accept verbal
promises. Be sure to compare the proposals to ensure the scope of
work in each proposal (project description) meets your needs and
are similar. Examine all terms of the proposal (e.g., price, project plan
and timeframe, use of subcontractors). Consider each contractor’s
experience with residential earthquake retrofitting. The lowest-priced
bid may not be the best bid.
Ask for and then check with references.
Before finalizing a contract, verify that your preferred contractor’s state
license is current and that your contractor is licensed to do business in
your community.
You will find useful a number of publications from the Contractor’s State
License Board. Visit www.cslb.ca.gov.
What You Should Know before Hiring a Contractor:
Provides information on how to find, hire and work with a contractor
A Consumer Guide to Home Improvement Contracts:
Provides information on the legal obligations of home improvement
contractors
Avoid Contractor Payment Pitfalls
For any project that costs $500 or more, a licensed contractor must
provide a written contract.
Pay the contractor in installments as the work is completed.
o
Keep the down payment low. By law, a down payment on a home
improvement contract cannot exceed 10% of the contract price or
$1,000, whichever is less.
o
Withhold at least 10% of the total contract price until the project is
completed to your satisfaction.
o
Do not make the final payment until the local building department
has signed off on the work and you have conducted a final review of
the work to make sure it is complete and correct.
PAGE 29
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Earthquake Safety Tips
Precautions: During an Earthquake
If you are indoors: Drop, cover and hold on.
Get under a sturdy desk or table and hang on to it OR move
into a hallway OR get against an interior wall.
Stay clear of windows, fireplaces, and heavy furniture or appliances.
Get out of a kitchen or any area that has numerous objects
that can fall.
Do not run downstairs or rush outside while the building is
shaking. Debris may be falling and/or you might fall and
sustain an injury.
If you are outdoors: Get into an open area.
Move away from buildings, power lines, chimneys, and anything
else that might fall on you.
If you are driving: Prepare to stop.
Move as far out of traffic as possible.
Do not stop on or under a bridge or overpass or under trees,
light poles, power lines, or signs.
Remain in your car until the shaking stops.
After you resume driving, watch for cracks or bumps in the
road and fallen objects.
If you are near a steep hillside: Watch for landslides.
Earthquakes can loosen rocks, trees, and other debris.
PAGE 30
DROP!
COVER!
HOLD ON!
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
COASTAL AREAS: SPECIAL TSUNAMI PRECAUTIONS
An earthquake or large landslide near the coast or beneath the ocean can
cause a tsunami. A tsunami may occur without warning, and the first waves—
which often are not the largest—may reach the coast within minutes after the
initial earthquake. And, an earthquake may result in more than one set of
waves; potentially deadly tsunami waves can continue to arrive for hours and
at intervals of 10 minutes or more.
During the shaking: Drop, cover, and hold on.
Watch for falling objects until the shaking stops.
After the shaking: Move (evacuate) immediately either to higher ground
or inland away from the shore, and do so on foot if you cannot evacuate by
vehicle. Note: Authorities may have no time to issue a warning. If you do not
hear an evacuation announcement but you see a drop or rise in water level or
you hear a loud noise coming from the water, move immediately and quickly
away from the shore.
Stay away from the shore. Wait for an official “all clear” announcement
before you return to the area.
GO TO HIGH
GROUND!
STAY THERE!
!
WAIT FOR
“ALL CLEAR”
PAGE 31
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Aftershocks
may occur and
you may need
to continue
to take
precautions
even after
the initial
earthquake.
Precautions: After an Earthquake
Check for Injuries
If a person is bleeding, put direct pressure on the wound.
Use clean gauze or cloth, if available.
If a person is not breathing, immediately call 911. If you can,
perform CPR.
Seek medical help for other serious injuries.
Do not attempt to move a person who is seriously injured
unless there is an immediate danger of further injury.
Cover injured persons with blankets to keep them warm.
Check for Hazards
Fires: If safe to do so, immediately extinguish a fire.
Otherwise, call 911.
Gas leaks: If you suspect a gas leak or smell natural gas (rotten
eggs), shut off the main gas valve. Note: Once you turn off the
gas,
do not turn it back on yourself. Wait for the gas utility
company to check for leaks and have the company restore
your service.
Damaged electrical wiring: Shut off your power at the
control box.
Downed or damaged utility lines: Do not touch downed
power lines or any objects in contact with them. Contact the
local electric utility company.
Spills: If you can do so safely, clean up any spilled medications or
spills of other potentially harmful materials such as bleach, lye,
or gasoline.
Downed or damaged chimneys: Approach chimneys with
caution; they may be weakened and could topple during
aftershocks. Do not use a fireplace with a damaged chimney;
the damage could cause a fire or leak toxic fumes into the home.
Broken glass: To avoid injuries, be sure to wear sturdy shoes.
Fallen objects: Look for objects that have fallen, being careful as
you check closets and cupboards for objects that still might fall.
PAGE 32
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Check Food and Water Supplies
Lack of electricity and meal planning: If you have no electricity, plan to
first eat refrigerated and frozen foods that will spoil quickly. Refrigerated
and frozen food will keep for at least two days if you do not open the
doors too often.
Using the stove: If you suspect a gas leak, do not turn on a stove. Even
an electric stove can create a spark that could cause an explosion.
Outdoor cooking: Only use barbecues or camp stoves outdoors.
Do not use them indoors.
MILK
PAGE 33
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Other Information
The pages that follow provide additional information that
homeowners may find useful.
Additional Resources
A number of additional resources on seismic safety and
earthquake safety for homeowners are available both from the
California Seismic Safety Commission and the Federal Emergency
Management Administration (FEMA).
California Seismic Safety Commission:
www.ssc.ca.gov/forms_pubs/hog.html
FEMA: www.fema.gov
California Building Standards Commission:
www.dgs.ca.gov/BSC/Codes
IN THIS SECTION PAGE
Additional Resources .............. 34
Relevant State
Seismic Safety Laws ................ 35
Earthquake Insurance .............. 37
Acknowledgments .................. 38
PAGE 34
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Relevant State
Seismic Safety Laws
The full wording of these laws is available at
http://leginfo.legislature.ca.gov/faces/codes.xhtml
Publishing the Guide (Business and Professions Code, Section 10149)
The California Seismic Safety Commission is required to develop, adopt,
publish, and update the Homeowner’s Guide to Earthquake Safety, containing
information on geologic and seismic hazards, explanations of structural
and nonstructural earthquake hazards, and recommendations for mitigating
these hazards.
Delivering this Guide (Government Code, Section 8897.1- 8897.5)
Sellers of homes built before 1960 with one to four units of conventional
light-frame construction must deliver to the buyer “as soon as practicable
before the transfer” a copy of the Homeowner’s Guide to Earthquake Safety
and disclose certain earthquake deficiencies. The seller’s real estate agent
must provide the seller with a copy of this Guide to give to the buyer.
Water Heater Bracing
(Health and Safety Code, Section 19211)
Water heaters must be anchored or strapped to resist falling during an
earthquake. The seller must certify to the potential buyer that the water
heater is properly braced.
Disclosing Risks
(Civil Code, Section 1102 and following sections)
Sellers of real property must disclose known defects and deficiencies in the
property—including earthquake risks and hazards—to prospective buyers.
Disclosing Natural Hazards
(Civil Code, Section 1103)
Sellers of real property must disclose, using the statutory Natural Hazard
Disclosure Statement, whether the property is within any of the seven mapped
natural hazard areas, including those areas with earthquake faults or those
areas with potential for landslides or liquefaction.
PAGE 35
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Earthquake Faults (Public Resources Code, Section 2621
and follow
ing sections)
The Alquist-Priolo Earthquake Fault Zoning Act prohibits building
for human occupancy astride active faults and requires sellers of
existing residences to disclose to potential buyers, on a Natural
Hazard Disclosure Statement, if the property is located in a
designated fault zone.
Landslide and Liquefaction
(Public Resources Code, Section 2694
and following sections)
The Seismic Hazard Mapping Act requires the State to prepare
maps of the zones in California most susceptible to landslide and
liquefaction hazards during earthquakes and requires sellers to
disclose to buyers, on a Natural Hazard Disclosure Statement, if the
property is in such a zone.
PAGE 36
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Earthquake Insurance
Companies that sell residential property insurance in California are required by
law to offer earthquake insurance to homeowners both at the time of initial sale
of the policy and then every two years at the time of policy renewal.
The cost of earthquake insurance coverage is based on a number of factors,
including a home’s location, age, construction type, and value.
Every home is different. In considering earthquake insurance, a homeowner
should evaluate the home’s individual risk factors and then weigh the cost of
earthquake coverage against the benefits. In other words, a homeowner should
determine a home’s potential for earthquake damage and the cost of repairs
and compare these costs against the cost of coverage (less the deductible that
is applicable to the policy). The advice of a licensed civil or structural engineer
or architect can be helpful in determining a home’s potential for damage and
expected costs of repairs.
The California Earthquake Authority (CEA) website has an online calculator to
help estimate earthquake insurance premiums. The calculator uses ZIP code,
insured value, dwelling type, and desired coverage and deductible to estimate
the premiums.
The CEA is required to provide, and the insurance companies are required to
disclose, the availability of discounts on earthquake insurance premiums for
older homes that have been strengthened to resist earthquake damage.
Residential insurance agents can also help homeowners locate earthquake
insurers and estimate annual premiums.
California Earthquake Authority
www.EarthquakeAuthority.com
California Department of Insurance
www.insurance.ca.gov
PAGE 37
HOMEOWNER’S GUIDE TO EARTHQUAKE SAFETY
Acknowledgments
California Seismic Safety Commission
Hon. Michael Gardner, Chair, Local Government
Mia Marvelli, Vice Chair, Building Standards Commission
Ida A. Clair, Acting State Architect
Hon. Ken Cooley, State Assembly (Alternate: Elizabeth Hess)
Mark Ghilarducci, Office of Emergency Services
Hon. Jerry Hill, State Senate (Alternate: Caitlin Armstrong)
Dr. Jorge Fernando Meneses, Geotechnical Engineer
Dr. Kit Miyamoto, Structural Engineer
Hon. David Rabbitt, Local Government
Hon. Cindy Silva, Local Government
Timothy Strack, Fire Protection
Fuad Sweiss, Mechanical Engineer
Andrew (Andy) Tran, Insurance
Ivan Wong, Seismologist
Commission Staff
Richard McCarthy, Executive Director
Robert Anderson
Lena Daniel
Michael Orille
Fred Turner
Salina Valencia
The Commission appreciates the assistance of the following organizations and
individuals in preparing this version and prior versions of the Guide:
American Red Cross
City of Los Angeles
American Society of Home
Earthquake Engineering Research
Inspectors
Institute
Association of Bay Area
Randy Goodwin, City Architect/Building
Governments
Official, City of West Sacramento
AT&T (SBC)
Humboldt Earthquake Education Center
Building Education Center
International Code Council
California Association of Realtors
San Diego Association of Governments
California Building Officials
Southern California Association
of Governments
California Council of the American
Institute of Architects
Southern California Gas
Company/SEMPRA
California Geological Survey
Structural Engineers Association
California Real Estate Inspection
of California
Association
California Governor’s Office of
Emergency Services
PAGE 38